FABRIC STRENGTHEN CONVEYOR BELT
Dimension(L*W*H): Customized Size Abrasion resistant Heat resistant Fire resistant Acid/Alkali resistant corrosion prevention Impact resistant Cold resistant skid resistant Anti-static
We have much experiences in fabrice strengthen rubber belt, this is our traditional products, our products have good sales in native market.
Specifications
Type: Fabric Strengthen Conveyor belt
Application:Horizontal transport /security check/electronic/chemical/agriculture
Dimension(L*W*H): Customized Size
Abrasion resistant
Corrosion prevention
Impact resistant
Oil resistant
Coldresistant
Heat resistant
Fire resistant
Acid/Alkali resistant
General Parameters
FabricMaterial | Code | Number of plies | Thickness of cover(mm) | Width (mm) | Length (m/roll) | |
| Top | Bottom | |||||
| Cotton Canvas | CC-65 | 1-12 | 1.5-40 | 0-10 | 300-6600 | 100-300 |
| Nylon | NN100 | 2-10 | ||||
| NN150 | ||||||
| NN200 | ||||||
| NN250 | ||||||
| NN300 | ||||||
| NN400 | ||||||
| Polyester | EP80 | 1-12 | ||||
| EP100 | 1-10 | |||||
| EP150 | ||||||
| EP200 | ||||||
| EP250 | ||||||
| EP300 | 1-6 | |||||
| EP400 | ||||||
| EP500 | ||||||
| EP600 | ||||||
The larger the number of the fabric material code, the larger of the thickness and intensity of the single layer fabric material. We can produce all kinds of fabric strengthen rubber belt according customers’ designation and design the most appropriate belt according to customers’ application.
Standard of different feature conveyor belt
Feature | Standard |
| Normal | GB7984-2001 |
| Heat resistant | HG2297 T1(≤100℃) T2(≤125℃) |
| High temperature resistant | HG2297 T3(≤150℃) |
| Fire resistanct | Resistant to ≥200℃ burning |
| Heat&abrasion resistant | Resistant to 125℃,abrasion loss≤150mm3 |
| Abrasion resistant | abrasion loss≤90mm3 |
| Flame retardant | GB10822-89 |
| Cold resistant | Brittleness temperature: -50℃ |
| Oil/Acid/Alkali resistant | HG-846 |
| PVC PVG | BS3289 MT914-2002 HG2805 |
1.Scope:
This procedure details the requirements for hot vulcanizing of solid woven belts with PVC, Nitrile and Neoprene covers and / or a combination of same, to make endless belts using fingersplicing method. The principle of this procedure shall be applied when splicing any belting made of solid woven carcass and impregnated with fire resistant antistatic PVC compound; and more particularly for ICL MINEPLAST fire resistant antistatic (FRAS) PVC conveyor belting as well as ICL Mineplast belt with Nitrile or Neoprene covers. Composition of FRAS compounds differs from one country to the other and also in between surface and underground application conforming to the regulatory standard of each country. Therefore, care shall be taken to ensure that proper compounds are used when undertaking any splicing work on solid woven FRAS PVC belting. The method of splicing described in these guidelines and the materials specified to be used have been developed to ensure that a high strength, reliable joint is achieved. Further, for high strength solid woven belts the finger method contained herein represent the preferred jointing methodology for these bets.
3 TOOLS & EQUIPMENT REQUIRED
a) White or yellow crayon pencil to draw datum and reference lines. b) Measuring Tape. c) Blade Knives (e.g. fixed blade or Olfa knife). d) Alligator Clamps with adequate cable pull. e) Vernier caliper for accurate measurement. f) Hand brush. g) Planer or slow speed rotary power tool with abrasive head. h) Cutting tool for cutting splice fingers as an alternate to blade knife. i) Spatula for spreading paste. j) Scissors. k) Vulcanizing Press complete with well calibrated electrical temperature and pressure controls, pressure and water hoses as required with temperature and pressure indicators. – Temperature accuracy ±3°C (±5°F) – 689 kPa (100 psi) minimum pressure capacity – Platten length = Splice length + 150mm or 6 inches (minimum) – Platten width = Belt width + 150mm or 6 inches (minimum) l) Two edge bars, approx. 100mm wide and 0.5-1mm thinner than the belt thickness, but approx. 300mm longer than the press length. m) Suitable clamping device for the type of Solid Woven belt (usually sash clamps). n) Template for marking splice.
SPLICING MATERIAL TO BE USED The dimensions and quantities of splice material are determined by the following:
5 SPLICING MATERIAL TO BE USED The dimensions and quantities of splice material are determined by the following:
1.Belt Type (Tensile Strength)
2. Belt Width
3. Belt Cover Thickness
4. Cover type The materials required for one splice are: a) Breaker Fabric: Width BFW = FL + PB +100mm Length = Belt width x 2 + 200mm (8 inches) b) PVC Paste (FRAS): High adhesive quality (Refer Table 2 for estimated quantity).
